top of page
Home / Products / La Rosita / Cables & Connectors / Speaker Cables
![]() | ![]() |
|---|---|
![]() | ![]() |
![]() | ![]() |
![]() | ![]() |
![]() |
SPEAKER CABLES
The common belief is that a cable is a completely passive element of the audio system. This is incorrect. A cable is a passive electrical circuit whose parameters have a considerable influence on the signal path, whether for interconnect cables or speaker cables. In most cases, you will therefore need to adjust the tonal balance of your audio system.All cables affect tonal balance, but some less than others.The rules for calculating cables have been known since the very early years of electronics and electroacoustics. They are very specific rules.The fact is that a cable is not a tone control and cannot be used to change the tonal balance of a system. Unfortunately, this is how cables are perceived and used.A cable with the least possible impact is the best choice for the tonal balance of a system; in a listening room, it must be adjusted using suitable acoustic elements, sometimes placed on the walls or in critical locations.The La Rosita cable uses materials perfectly suited to the transport of low frequency signals and are designed to impart no distinctive sonic signature.The chosen insulator is... air, which is why our cables are made of metal strands (very pure silver-plated copper) surrounded by several layers of silk and cotton. The silk and cotton trap a thin layer of air, which then becomes the insulation for our cables.
Theories about the cable were described by Georg Simon Ohm, a German physicist who died in Munich in July 1854.He established, very early on, EVERYTHING that governed the movement of electric current.All conductors are said to be ohmic, meaning they all oppose the flow of current through their resistance. There are conductors called superconductors, which do not oppose this resistance, but they are unstable and only become truly superconducting at temperatures lower than -250 °C.All theories about conductors or cable structures that improve sound are just nonsense.There are different grades of copper and silver, some used for plumbing or for making cookware. Silver, on the other hand, is a soft metal that must be alloyed with other metals to create fine cutlery.The characteristics that vary the properties of a cable are the metals that constitute it and the platings with which it is coated by electrolysis to play on a parameter called "skin effect" which must be put into perspective.Electrons move faster on the periphery of conductors and slower as they approach the core of a strand of conductive metal. This difference in speed is unavoidable regardless of the metal and, more importantly, only affects the electrical and conductive behavior of the metal at very high frequencies, on the order of 250 kHz to 400 kHz! These frequencies are therefore inaudible and barely measurable with state-of-the-art equipment. We must never forget that sound reproduction falls within a domain called low frequencies or "LF" and only covers the audible band, which, barring anomalies, can be located between 15,000 and 25,000 Hz (to be generous).Given all this, from an audible or technical standpoint, the cable's properties remain virtually unchanged. For your information, copper used for electrical conductors, including those running through your walls, has been oxygen-free (OFC) for over half a century.Since copper is an ore, it is necessary to heat this ore until the metal is extracted and then separate it by electrolysis. This electrolysis naturally deoxygenates it. The extraction and refining process is carried out in a single operation.In audio, another parameter can have an impact: cable impedance. However, a cable will never drastically alter the impedance matching between a device and the one before or after it. There remains Pierre Johannet's theory, called MDI (or Micro Interface Discharge), which could be described as an interaction between the dielectric (the insulator covering the copper strand) and the copper strand itself.It would be a kind of halo of particles which, all around each cable, could modify its behavior by the mechanical excitation of the air, caused among other things by the loudspeakers of the system which are located in the listening room.All of this leads us to wonder: "So, why is La Rosita building cables???"Simply because what you find in the industry, and especially the most expensive stuff, is sometimes so strangely constructed that it doesn't even respect the basic rules of building a cable dedicated to audio.What MaterialsWhich sectionWhat rulesTo this we have our own answers, logical, simple and in accordance with the theories of Georg Simon OhmWe chose silver-plated copper, guaranteeing at least that the surface of the copper would never oxidize.We analyzed the quality of the signals to be transported in LF (currents, voltages, average impedances and distances over which the signal is transported) and we realized that the range was VERY WIDE on all of these criteria before disturbing or affecting the transport of the signal and its integrity.As a precaution, we chose "AIR" as the insulation, meaning we covered our silver-plated copper strands with silk and cotton. (Silk has a "better grip," preventing the cotton from slipping on the strand while still allowing air to circulate.)As cotton has natural water-repellent properties, silk and cotton combine well.By offering a La Rosita cable, we hope that users will get closer to our spirit, without artifice.This also prevents some people from spending fortunes that have no relation to the price a good audio cable should cost….
bottom of page








